![]() ![]() Greetings fellow Spicepeople and welcome to another working week. Spark! Pro Series - 7th August 2023 Spiceworks Originals.Snap! - Acoustic Hack, Professional Uno, Tahoe Trashbots, Blindness Cure? Spiceworks Originalsįlashback: August 7, 1944: IBM presents ASCC Giant Brain to Harvard (Read more HERE.)īonus Flashback: August 7, 1954: First space cabin simulator (Read more HERE.).I could fix this by paying extra 10 bucks or stick with coax, but I will ask this to you guys. Is this Possible. I recently upgraded my ISP from Coax to Fiber, but I was not aware of CGNAT and it killed a lot of my stuff i had port forwarding mainly plex. Home Network Puzzle help needed Networking.e1000e 0000:00:1f.6 eno1: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Txĥ.25"/1.2 MB floppy services are supported (int 13h)ģ.5"/720 kB floppy services are supported (int 13h)ģ.5"/2. e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode e1000e: Intel(R) PRO/1000 Network Driver Subsystem: Lenovo Ethernet Connection (2) I219-LM Supported link modes: 10baseT/Half 10baseT/FullĪdvertised link modes: 10baseT/Half 10baseT/FullĠ0:1f.6 Ethernet controller : Intel Corporation Ethernet Connection (2) I219-LM (rev 31) Oct 18 23:10:52 pve systemd: wol.service: Succeeded. ![]() Oct 18 23:10:52 pve systemd: Started Wake-on-LAN for eno1. Main PID: 950 (code=exited, status=0/SUCCESS) Process: 955 ExecStop=/sbin/ethtool -s eno1 wol g (code=exited, status=0/SUCCESS) Process: 950 ExecStart=/sbin/ethtool -s eno1 wol g (code=exited, status=0/SUCCESS) Loaded: loaded (/etc/systemd/system/wol.service enabled vendor preset: enabled)Īctive: inactive (dead) since Mon 23:10:52 CEST 1min 57s ago Sudo chmod 755 /etc/rc0.d/wol_poweroff.sh & sudo chmod 755 /etc/rc6.d/wol_poweroff.sh Created script to bring the ethernet interface down properly at shutdown :Ĭp /etc/rc6.d/wol_poweroff.sh /etc/ rc0.d/wol_poweroff.shįinally changed permissions to make it executable: I tried sending packets to the combination of host's MAC and IP (as well as broadcast to 255.255.255.255), ports 7,9,4343,4000,etc.When the machine is powered off, and I send magic packets using apps like "wol" (from a windows host), an android app (landroid), I understand that they are reaching the NIC as I can see the ethernet port flashing, but the machine doesn't boot.When the machine is powered on, I successfully tested receiving magic packets using netcat.I also created a systemd service " wol.service", to also set the eno1 interface's wol to "g", using ethtool (see #3 below).Created script to bring the ethernet interface eno1 down properly at shutdown, based on this bug (see #2 below).Updated cat /etc/network/interfaces so that at every boot, it sets the vmbr0 interface's wol to "g", using ethtool (see #1 below).The NIC supports WoL and is (/was already correctly) enabled and set to "g".The BIOS (is up-to-date) supports WoL and is enabled.At this point I am not sure if it is a configuration issue or a BUG? I can't get Wake on Lan (WOL) to work with Proxmox, no matter what. I then installed Proxmox 7 (5.11.22-4-pve) on the same hardware. ![]() I was able to wake up the system from a "Hibernate" or "Sleep" mode by sending a magic packet from another windows host. disable "reduce speed on power down") and the UEFI BIOS to make it work. I had to make some changes in the adapter settings (eg. I confirmed that Wake On Lan works with Windows 10 Pr o on a Lenovo ThinkStation P310 with onboard Intel I219-LM GB Ethernet controller. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |